Gtir Motorsport club

Welcome to the largest Nissan Pulsar & Sunny GTI-R Forum. Masses of info, friendly members, cars for sale, lots of spares. Best forum on the net by far. Everything your gtir needs is here.


You are not connected. Please login or register

Gtir Motorsport club » General Discusion » Gtir related Discussion » Got mine mapped today

Got mine mapped today

Go down  Message [Page 1 of 1]

1 Got mine mapped today on 16th October 2018, 5:48 pm

astarozna

avatar
Took it finally to a mapper today. Healthy 340bhp at1.3bar limiting factor was barrel cooler. Need a bigger one Twisted Evil

2 Re: Got mine mapped today on 16th October 2018, 5:57 pm

Biggs

avatar
Good figures there. What other supporting mods is it running?



Last edited by Biggs on 16th October 2018, 6:10 pm; edited 1 time in total

3 Re: Got mine mapped today on 16th October 2018, 6:09 pm

astarozna

avatar
The usual supporting bits and bobs. Hybrid garret 3071, 800cc injectors, pwr barrel cooler, ecu

4 Re: Got mine mapped today on 16th October 2018, 6:11 pm

Biggs

avatar
Are you still running a dizzy or COP?

5 Re: Got mine mapped today on 16th October 2018, 6:21 pm

astarozna

avatar
Stock dizzy at the moment.

6 Re: Got mine mapped today on 16th October 2018, 6:25 pm

Gostek

avatar
Events Organiser
Events Organiser
What size barrel you've got bud? And what sort of temps you had at wot? still 340hp that ain't bad!


_________________

7 Re: Got mine mapped today on 16th October 2018, 6:28 pm

astarozna

avatar
It's that one that flows up to 320bhp. idle was 35 and at wot spiked up to 54 if remember right so need to address that

8 Re: Got mine mapped today on 16th October 2018, 6:41 pm

Biggs

avatar
Sweet...Never seen one on an R before.... Can't help but think a front mount intercooler would be more efficient and easier to install??

9 Re: Got mine mapped today on 16th October 2018, 6:47 pm

Gostek

avatar
Events Organiser
Events Organiser
@Biggs wrote:Sweet...Never seen one on an R before.... Can't help but think a front mount intercooler would be more efficient and easier to install??

But there's no fun in that lol!

I've got 5x10 barrel apparently good for 500... I need to actually thrash t properly see how high they'll go atm is around 40 degree. But there again my mate got ebay jobby front mount and his goes to 50 when thrashed...

I actually got chargecooler just so I don't have to cut my bumper but if it'll go too high temp I'll stick meth injection (I'll stick one anyway) since emu can control pump and switch maps if I'll run out of meth.


_________________

10 Re: Got mine mapped today on 16th October 2018, 6:49 pm

Gostek

avatar
Events Organiser
Events Organiser


I'll stick photo of mine as well cos I'm sad and looking for attention lol! lol! lol! lol! lol!


_________________

11 Re: Got mine mapped today on 16th October 2018, 6:53 pm

Biggs

avatar
I like it....it's different.

12 Re: Got mine mapped today on 16th October 2018, 6:53 pm

Biggs

avatar
What trigger set-up did you use for the COP?

13 Re: Got mine mapped today on 16th October 2018, 7:00 pm

astarozna

avatar
lol! , sadly Gems ecu lacks all of the inventions after "93 but i have motec waiting to go in. I do have a front mount intercooler as well in the garage with the short run pipes but no rad that will let the pipes run over it. So either a bigger barrel or custom rad. Are those audi cops?

14 Re: Got mine mapped today on 16th October 2018, 7:16 pm

Gostek

avatar
Events Organiser
Events Organiser
I still run standard cas Biggs so far no problem will see in few weeks when I'll be raising rev limiter (7.5k atm). Astarozna yeah ngk replacement for r8/tfsi.


_________________

15 Re: Got mine mapped today on 16th October 2018, 8:07 pm

mike74

avatar
Not seen those barrels before, im intrigued!

16 Re: Got mine mapped today on 16th October 2018, 10:49 pm

Gostek

avatar
Events Organiser
Events Organiser
@mike74 wrote:Not seen those barrels before, im intrigued!

Look for liquid to air charge cooler. Opinions are divided tho.


_________________

17 Re: Got mine mapped today on 16th October 2018, 11:10 pm

ducie54

avatar
What size water pump and Water cooler do u have? Most people don't run enough water flow.

18 Re: Got mine mapped today on 17th October 2018, 5:45 am

astarozna

avatar
You're right. I have a short run, boat bilge pump, m5 rad and no tank although i have one but i'd have to run it from the trunk and the piping needs to go from inside. Come winter and the pipes would freeze over if i'd run them from underneath the car. I just wanted to try the barrel setup, i now have a reference point to compare with air-to-air setup.

19 Re: Got mine mapped today on 17th October 2018, 6:18 pm

Gostek

avatar
Events Organiser
Events Organiser
@ducie54 wrote:What size water pump and Water cooler do u have? Most people don't run enough water flow.

What sort of pump you've got mate?
Mine is bosch aux pump from audi but I'm wondering if I won't need bigger one too.


_________________

20 Re: Got mine mapped today on 17th October 2018, 6:28 pm

astarozna

avatar
This one but it seems that bosch flows 20lpm
https://www.osculati.com/en/11142-16.512.12/europump-12-4-diaphragm-fresh-water-pump-12-v

21 Re: Got mine mapped today on 17th October 2018, 10:45 pm

ducie54

avatar
@Gostek wrote:
@ducie54 wrote:What size water pump and Water cooler do u have? Most people don't run enough water flow.

What sort of pump you've got mate?
Mine is bosch aux pump from audi but I'm wondering if I won't need bigger one too.

I'm running a Davis craig 80L/min pump. Which was the biggest they sold when I bought it. If it breaks I'll go bigger agian. Cooler is a 600*300*40mm core.

You just need to watch head pressure as some pumps don't like it and the flow drops off really quick. Also look at bleeding the air from the barrel, depending on the entry exit hoses you may end up with a air cavity. I put air bleeds on top of mine as the water pipes come in from the side.

Water to air cost more and and extra weight for me is worth it. I like the short pipe run and my temps stay consistent.

22 Re: Got mine mapped today on 18th October 2018, 5:51 am

astarozna

avatar
Good to know.thumbsup I have angled it that way that there shouldn't be any air in the barrel. Heat exchanger is way to small 200mm x 200mm. I had it laying around so thought i'll give it a go, have bigger one as well.

Sponsored content


Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum